@gotgenes/pi-subagents-worktrees

Git worktree isolation for @gotgenes/pi-subagents.

This extension registers a WorkspaceProvider with the subagents core: opted-in agents run in a temporary git worktree (an isolated copy of the repo), and any changes they make are saved to a branch when they finish. Worktrees are one workspace strategy, not core behavior — so the git plumbing lives here, outside the minimal subagents core (see ADR-0002 in the pi-subagents package).

Install

Install after @gotgenes/pi-subagents. Pi loads packages in the order they are listed in .pi/settings.json, and this extension registers its provider with the subagents service at load time — so the subagents core must load first.

{
  "packages": [
    "npm:@gotgenes/pi-subagents",
    "npm:@gotgenes/pi-subagents-worktrees"
  ]
}

If @gotgenes/pi-subagents is not loaded first (or not installed at all), this extension does nothing.

Configuration

Worktree isolation is opt-in per agent type. List the agent types that should run in a worktree in a subagents-worktrees.json file:

• Global: ~/.pi/agent/subagents-worktrees.json
• Project: <cwd>/.pi/subagents-worktrees.json (overrides global)

{
  "worktreeAgents": ["general-purpose", "refactorer"]
}

An agent type not in worktreeAgents runs in the parent working directory, exactly as if this extension were not installed.

Behavior

• A child whose agent type is listed gets a fresh detached worktree at HEAD before it runs.
• When the child finishes with no changes, the worktree is removed.
• When the child finishes with changes, they are committed to a branch (pi-agent-<id>), and the child's result gains a note: Changes saved to branch \`. Merge with: `git merge ``.
• If a commit hook rejects that commit, it is retried once with --no-verify, because the commit exists to rescue work the child already did and a rejecting hook would otherwise cost you that work. Files a hook rewrote before failing are re-staged, so a formatter's corrections are committed rather than discarded. The note then gains a second line reading Commit hooks were bypassed to save this work — review the commit before merging.
• If cleanup fails for any other reason, the worktree is left in place rather than removed, and the child's result gains a note: Worktree cleanup failed; the worktree was left in place at \` for manual recovery: `. Nothing is deleted while its state is uncertain, so the work stays recoverable.
• If worktree creation fails for an opted-in agent (not a git repo, no commits yet, or git worktree add fails), the child run fails with an explanatory error rather than silently running unisolated.
• At the start of every session with a UI, any rescue worktrees still on disk are named in a warning, so a preserved worktree is not forgotten once the child's result scrolls out of view.

Recovering preserved worktrees

A preserved worktree is a plain git worktree with the agent's work still in it. Inspect it with git -C <path> status, and recover the work however you normally would — commit it on a branch, or copy the files out.

Run /subagents-worktrees at any time to list the preserved worktrees for the current repository. Selecting one offers to remove it, and removal happens only after you confirm — nothing here is ever deleted automatically, because a failed cleanup is exactly the case where the content is not safe to discard on the extension's judgment.

A worktree is listed when it is registered with the repository, named with this package's pi-agent- prefix, still on disk, and not currently in use by a child of this session. A worktree belonging to a different Pi process running against the same repository cannot be told apart from an abandoned one, so it is listed too — check the path before removing anything.

Migrating from isolation: "worktree"

Earlier versions of @gotgenes/pi-subagents accepted an isolation: "worktree" spawn flag. That flag was removed from the core; install this package and list the agent types you want isolated in worktreeAgents instead.

License

MIT